Prep Master Bush Hammer Plate for Concrete Floor

Prep Master Bush Hammer Plate for Concrete Floor Type:Prep Master Bush Hammer Plate for Concrete Floor Fitted to put on different sizes of bush hammer plates. APPLICATIONS: 1. To create anti-slip surfaces. 2. To remove old glue and resin coatings, in particular thick resins. 3. To use as a scarifying machine with the advantage that it is aggressive but gentle enough not to “dig” uncontrollably into the floor surface. 4. For floor preparation before laying new coatings. 5. To expose the aggregate in concrete floors to prepare for concrete polishing.

HTC Floor Grinding Shoes

HTC grinding shoes are designed for thin mil coating removal, mastic removal, and for the first steps in polishing.   We offer these diamonds in double bar and single bar segment design,of course can also be rounds or arrow segments .    We offer three bonds soft, medium, and hard.   Grinding plate fit on HTC floor grinder machine   Grit:16#, 30/40#, 60/80#, 120/150# or other grits according to your request.   Segment size:40x10x10mm or 40x12x12mm 

Bar Segments 240mm Klindex Metal Bond Diamond Grinding Ring with 3 Pins

 Metal Bond Diamond Grinding Ring with 3 Pins are designed for grinding concrete,granite, terrazzo and travertine etc. and for the first steps in grinding.   Size:240mm diameter, with 3 pins.   There are 12 pieces segments on the metal body.   Segment size:10mm height   Grit:16#-400#    We offer three bonds soft, medium, and hard; and also make very soft, very hard bond.   Fitted to Klindex floor machine.

8 Triangles Diamond 3 Inch Resin Floor Polishing Pads

8 Triangles Diamond 3 Inch Resin Floor Polishing Pads 1. Extra thick segments designed for long product life. 2. 10 mm thick diamond discs are the thickest on the market. 3. Female velcro back - attaches to any male velcro face. 4. Excellent for surface polishing and floor restoration of marble, terrazzo, travertine.       3 Inch Diamond Velcro Concrete Floor Polishing Pads are a high quality long lasting resin bond diamond polishing disc used to restore and polish a variety of stone floor surfaces. It may be used under a variety of floor machines, including single disc floor machines, hand held polishers as well as multiple head machines like the Cimex. The Typhoon diamond pads perform well on a variety of hard surfaces including Marble, Terrazzo, Limestone, Travertine, leaving a flat, highly polished surface.     1. Average life of the diamond discs ranges from 3,000-5,000 sq ft. depending on floor condition, density (hardness of the stone) and lippage (unevenness of the tile). 2. Wider range of operating RPM's from 150 to 3500. 3. Higher quality diamonds with multiple edges are used. 4. Up to 3 times more diamonds per pad than competitors discs. 5. The longest lasting resin bond diamonds you can buy. Diamond discs are available in the following grits: 50#-100#-200#-400#-800#-1500#-3000#

Single Bar Double PCD Diamond Grinding Traps for Diamatic Floor Grinder

Split Lavina PCD Diamonds for Epoxy Floor Removing is an excellent choice when removing medium/heavy coatings. The design and positioning of the PCD with an aggressive diamond segment acting as a stabilizer and depth guide scrapes the thickest of coatings aggressively and follows with a conventional grind all in one pass. These PCD's are directional specific and come in clockwise and counterclockwise orientation.  •••IMPORTANT: If you run a rotary machine with counter rotating heads, be sure to get 1/2 clockwise and 1/2 counter clockwise PCDs when you order.  The weight of the machine is partially supported by the large surface area of the diamond segment - this segment limits the PCD's penetration into the concrete. The diamond segment lightly dresses and helps remove the severe marks left by the PCD grinding teeth. This configuration will yield a higher total square foot life span while providing an aggressive rate of coating and concrete removal. Use these PCD tools to remove heavy coatings, overcoats, glues, mastics, thin set and paint.  PCD (polycrystalline diamond) is the result of sophisticated high-pressure, high-temperature technology in which carefully selected synthetic diamond particles are sintered together in a cobalt matrix. PCD product usually consists of two layers. The PCD layer (usually black) is diamond particles which have been sintered together into a coherent structure using a chemo-mechanical binder and high-pressure, high-temperature conditions similar to those used in single crystal diamond synthesis. The polycrystalline diamond layer is integrally bonded by an advanced process to a super tough tungsten carbide substrate which provides strength and permits welding or brazing with other metals. The random orientation of the diamond particles produces a high uniform hardness four times stronger than carbide with remarkable wear resistance.

6 Segments Grinding Disc With Post For Concrete Grinding

This kind of  6 segment metal bond grinding disc is designed for quick removal of thinset, glue & mastics an ideal tool substrate preparation. Use wet or dry. Attachment system:Post(15mm length or 7mm length) Bond:hard,soft,medium Grit:16/20#,30/40#,60/80#,120/150#